Permit Search | Palm Coast Connect (2024)

Status Location Address Mailing Address State License Number Phone ACTIVE

50 LEANNI WAY

PALM COAST, FL 32137

UNIT C-1

PALM COAST, FL 32137

CBC1260957 (Exp: 08/31/2024) 386-447-4151
Status Location Address Mailing Address State Liscense Number Phone ACTIVE

15 HARGROVE LN

PALM COAST, FL 32137

1G

PALM COAST, FL 32137

EC13006037 (Exp: 08/31/2026) 386-586-9144
Status Location Address Mailing Address State Liscense Number Phone ACTIVE

2820 LEWIS SPEEDWAY

ST AUGUSTINE, FL 32084

STE B

ST AUGUSTINE, FL 32084

CAC1820713 (Exp: 08/31/2024) 904-342-5709
Status Location Address Mailing Address State Liscense Number Phone ACTIVE

840 DELTONA BLVD

DELTONA, FL 32725

STE F2

DELTONA, FL 32725

CCC1327280 (Exp: 08/31/2024) 386-575-4007
Status Location Address State Liscense Number ACTIVE

1328 COUNTY ROAD 308

CRESCENT CITY, FL 32112

RF11067806 (Exp: 08/31/2025)
Type Request Date Result Inspector INSULATION 06/06/2024 Disapproved -FEE REQUIRED MKRASKI Note: 6/6/24Nail plate still missing from previous inspection5/31/2024 - PREVIOUS INSPECTION NOTES5/31/24: 1). Fireblocking (minimum 1-1/2" thick per FBC-R302.11.1) required in garage where dryer exhaust, vent stack & electric wires enter attic space. Also, will need firestopat any seams & perimeter.Also, you will need to expose the top plate where the nail plate was missing previously so we can verify that it was resolved.5/28/2024 - PREVIOUS INSPECTION NOTESInspector Notes from Inspection 24205/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet.5-28-241. Need fire blocking in master shower.2. Need fire blocking at entry from garage to house on right side wall.3. Need fire blocking/ foam at electrical panels, vent pipe and dryer duct.4. Silt fence is still down. INSULATION 06/06/2024 APPROVED MKRASKI Note: 6/6/2024 - PREVIOUS INSPECTION NOTES6/6/24Nail plate still missing from previous inspection5/31/2024 - PREVIOUS INSPECTION NOTES5/31/24: 1). Fireblocking (minimum 1-1/2" thick per FBC-R302.11.1) required in garage where dryer exhaust, vent stack & electric wires enter attic space. Also, will need firestopat any seams & perimeter.Also, you will need to expose the top plate where the nail plate was missing previously so we can verify that it was resolved.5/28/2024 - PREVIOUS INSPECTION NOTESInspector Notes from Inspection 24205/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet.5-28-241. Need fire blocking in master shower.2. Need fire blocking at entry from garage to house on right side wall.3. Need fire blocking/ foam at electrical panels, vent pipe and dryer duct.4. Silt fence is still down. INSULATION 06/05/2024 CANCELLED BY APPLICANT WEB Note: 5/31/2024 - PREVIOUS INSPECTION NOTES5/31/24: 1). Fireblocking (minimum 1-1/2" thick per FBC-R302.11.1) required in garage where dryer exhaust, vent stack & electric wires enter attic space. Also, will need firestopat any seams & perimeter.Also, you will need to expose the top plate where the nail plate was missing previously so we can verify that it was resolved.5/28/2024 - PREVIOUS INSPECTION NOTESInspector Notes from Inspection 24205/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet.5-28-241. Need fire blocking in master shower.2. Need fire blocking at entry from garage to house on right side wall.3. Need fire blocking/ foam at electrical panels, vent pipe and dryer duct.4. Silt fence is still down. INSULATION 05/31/2024 Disapproved - NO FEE RSIMS Note: 5/31/24: 1). Fireblocking (minimum 1-1/2" thick per FBC-R302.11.1) required in garage where dryer exhaust, vent stack & electric wires enter attic space. Also, will need firestopat any seams & perimeter.Also, you will need to expose the top plate where the nail plate was missing previously so we can verify that it was resolved.5/28/2024 - PREVIOUS INSPECTION NOTESInspector Notes from Inspection 24205/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet.5-28-241. Need fire blocking in master shower.2. Need fire blocking at entry from garage to house on right side wall.3. Need fire blocking/ foam at electrical panels, vent pipe and dryer duct.4. Silt fence is still down. INSULATION 05/28/2024 Disapproved -FEE REQUIRED BTAYLOR Note: Inspector Notes from Inspection 24205/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet.5-28-241. Need fire blocking in master shower.2. Need fire blocking at entry from garage to house on right side wall.3. Need fire blocking/ foam at electrical panels, vent pipe and dryer duct.4. Silt fence is still down. ALL ROUGH 05/21/2024 APPROVED - AS NOTED RSIMS Note: 5/21/24: Approved as noted to keep project moving. MUST BE COMPLETE PRIOR TO NEXT INSPECTION. Check at next inspection. 1). Nail plates in laundry room are incomplete. Only 1 installed at the double top plate.2). Please repair your silt fence and keep it maintained throughout the build process to avoid failed inspections with fee. FBC 3307.15/14/2024 - PREVIOUS INSPECTION NOTES5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet. ALL ROUGH 05/14/2024 Disapproved -FEE REQUIRED RSIMS Note: 5/14/24:1). Missing Nail Plates for wire protection: (Marked with NP where needed) - 2-laundry / 2-left side / 1-middle closet / 2-Master Bedroom / 1-garage. Please check all that are under 1-1/4" minimum from stud/plate face.2). No water pressure.3). Shower faucet plumbing is incomplete. 4). Wires for Mechanical equipment are not phased out.5). Kitchen exhaust is missing the 3 screws at connections as required. M1601.4.1Crimp joints for round metallic ducts shall have a contact lap of not less than 1 inch (25 mm) and shall be mechanically fastened by means of not less than three sheet-metal screws or rivets equally spaced around the joint.6). Shingles installed but dryer gooseneck & plumbing vent stack boots are not installed.7). Need a revision for the different windows installed (5823.1) than what shows on the submitted product approval sheet. LATH/BRICK/ WATER BARRIER 05/14/2024 APPROVED RSIMS ROOF VALLEY & METAL 04/17/2024 APPROVED RSIMS Note: 4/16/2024 - PREVIOUS INSPECTION NOTES4/16/24: Previously noted 2 ply truss 28 remains unresolved. (2 rows - 4"OC). Please look at highlighted information on plans as stated before.Previously listed item 1 below: The flashing needs to be mechanically fastened to the wall with drive pins, tapcons or similar. Roof cement alone is not a sufficient means of attaching.4/10/2024 - PREVIOUS INSPECTION NOTES4/10/24: 1). 5" x 5" wall flashing needs to be sealed to the wall along the top leg as required by Manufacturer.2). 5" x 5" flashing at left side of entry needs to be anchored to concrete wall and sealed as required.* Also, 2ply truss 28 still needs to be connected as required on MiTek along the bottom cord.Inspector Notes from Inspection 24603/28/24: Must be complete by next inspection.1). 2ply trusses - 08, 22 and 28 are not connected as required. Highlighted on MiTek. Each row has to meet OC spacing individually. 2). 09 truss has a split web which will need repair per MiTek requirements.Inspector Notes from Inspection 2450Check the following by next inspection1. missing blocking at panel edges (paned edges cannot be properly nailed at collumns, missing blocking/backing) Peer manufacturer specs2. Need repairs to silt fence by next inspection (right side fence is down) ROOF VALLEY & METAL 04/16/2024 Disapproved -FEE REQUIRED RSIMS Note: 4/16/24: Previously noted 2 ply truss 28 remains unresolved. (2 rows - 4"OC). Please look at highlighted information on plans as stated before.Previously listed item 1 below: The flashing needs to be mechanically fastened to the wall with drive pins, tapcons or similar. Roof cement alone is not a sufficient means of attaching.4/10/2024 - PREVIOUS INSPECTION NOTES4/10/24: 1). 5" x 5" wall flashing needs to be sealed to the wall along the top leg as required by Manufacturer.2). 5" x 5" flashing at left side of entry needs to be anchored to concrete wall and sealed as required.* Also, 2ply truss 28 still needs to be connected as required on MiTek along the bottom cord.Inspector Notes from Inspection 24603/28/24: Must be complete by next inspection.1). 2ply trusses - 08, 22 and 28 are not connected as required. Highlighted on MiTek. Each row has to meet OC spacing individually. 2). 09 truss has a split web which will need repair per MiTek requirements.Inspector Notes from Inspection 2450Check the following by next inspection1. missing blocking at panel edges (paned edges cannot be properly nailed at collumns, missing blocking/backing) Peer manufacturer specs2. Need repairs to silt fence by next inspection (right side fence is down) ROOF VALLEY & METAL 04/10/2024 Disapproved - NO FEE RSIMS Note: 4/10/24: 1). 5" x 5" wall flashing needs to be sealed to the wall along the top leg as required by Manufacturer.2). 5" x 5" flashing at left side of entry needs to be anchored to concrete wall and sealed as required.* Also, 2ply truss 28 still needs to be connected as required on MiTek along the bottom cord.Inspector Notes from Inspection 24603/28/24: Must be complete by next inspection.1). 2ply trusses - 08, 22 and 28 are not connected as required. Highlighted on MiTek. Each row has to meet OC spacing individually. 2). 09 truss has a split web which will need repair per MiTek requirements.Inspector Notes from Inspection 2450Check the following by next inspection1. missing blocking at panel edges (paned edges cannot be properly nailed at collumns, missing blocking/backing) Peer manufacturer specs2. Need repairs to silt fence by next inspection (right side fence is down) ROOF SHEATHING / BRACES/TIES/DOWN CELL 03/28/2024 APPROVED - AS NOTED RSIMS Note: 3/28/24: Must be complete by next inspection.1). 2ply trusses - 08, 22 and 28 are not connected as required. Highlighted on MiTek. Each row has to meet OC spacing individually. 2). 09 truss has a split web which will need repair per MiTek requirements.Inspector Notes from Inspection 2450Check the following by next inspection1. missing blocking at panel edges (paned edges cannot be properly nailed at collumns, missing blocking/backing) Peer manufacturer specs2. Need repairs to silt fence by next inspection (right side fence is down) WALL SHEATHING 03/25/2024 APPROVED - AS NOTED LMILLER Note: Check the following by next inspection1. missing blocking at panel edges (paned edges cannot be properly nailed at collumns, missing blocking/backing) Peer manufacturer specs2. Need repairs to silt fence by next inspection (right side fence is down) TIE BEAM / LINTEL 02/16/2024 APPROVED RSIMS FOUND SURVEY APPROVED (OFFICE) 02/06/2024 APPROVED TBAKER MONOLITHIC SLAB 01/25/2024 APPROVED RSIMS Note: 1/23/2024 - PREVIOUS INSPECTION NOTES1/23/24: * 6 mil plastic has blown off of slab area. Please re-secure at seams thoroughly to prevent a re-occurrence.1/19/2024 - PREVIOUS INSPECTION NOTES1/19/24: 1). Rear Middle column footer has rebar that does not have the minimum 3" ground clearance as required.2). Rear footer has roots that need to be removed. Highlighted on plan.* Please clean out minor washin dirt throughout a few areas of the footers to maintain 3" clearance for rebar. MONOLITHIC SLAB 01/23/2024 Disapproved -FEE REQUIRED RSIMS Note: 1/23/24: * 6 mil plastic has blown off of slab area. Please re-secure at seams thoroughly to prevent a re-occurrence.1/19/2024 - PREVIOUS INSPECTION NOTES1/19/24: 1). Rear Middle column footer has rebar that does not have the minimum 3" ground clearance as required.2). Rear footer has roots that need to be removed. Highlighted on plan.* Please clean out minor washin dirt throughout a few areas of the footers to maintain 3" clearance for rebar. MONOLITHIC SLAB 01/19/2024 Disapproved - NO FEE RSIMS Note: 1/19/24: 1). Rear Middle column footer has rebar that does not have the minimum 3" ground clearance as required.2). Rear footer has roots that need to be removed. Highlighted on plan.* Please clean out minor wash-in dirt throughout a few areas of the footers to maintain 3" clearance for rebar. PLUMBING 1ST ROUGH UNDERGROUND 01/12/2024 APPROVED - AS NOTED MGIBSON Note: HAVE CORRECT PLUMBING SUB CONTRACTOR CHANGED TO CORRECT ONE BY NEXT INSPECTION WATER METER INSTALLATION REQUEST 12/04/2023 APPROVED CBOWERMASTER Note: 11/22/2023 3:16:42 PM- PREVIOUS INSPECTION NOTES wooded lot WATER METER INSTALLATION REQUEST 11/22/2023 Disapproved -FEE REQUIRED CBOWERMASTER Note: wooded lot BLD - BUILDING FINAL PEP TANK INSTALLATION REQUEST U-CROSS CONNECTION ROW- PRE-APRON (PRE-POUR) ROW - FINAL APRON (AFTER POUR) ROW - FINAL SURVEY (OFFICE USE ONLY) FIELD SURVEY ROW - STORMWATER FINAL U -UTILITY RESIDENTIAL FINAL GRAVITY SEWER TEST SEWER TIE IN ELECTRIC - EARLY POWER
Department Status Date In Date Out BLD COMPLETE 05/14/2024 05/20/2024 Note: Released By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COMKS ZON COMPLETE 02/06/2024 02/06/2024 Note: Released By: MICHELLE RAMOS - (386)986-3780 - MRAMOS@PALMCOASTGOV.COM ENGIN1 COMPLETE 02/06/2024 02/06/2024 Note: Released By: TIM BAKER - (386)986-4726 - TBAKER@PALMCOASTGOV.COM ZON COMPLETE 01/10/2024 01/10/2024 Note: Released By: ALISHA MOBLEY - (386)986-3751 - AMOBLEY@PALMCOASTGOV.COM ZON COMPLETE 11/06/2023 11/08/2023 Note: Released By: KATIE TAING - (386)986-3751 - KTAING@PALMCOASTGOV.COM ELEC COMPLETE 11/06/2023 11/07/2023 Note: Released By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM SW1 COMPLETE 11/06/2023 11/17/2023 Note: Released By: JEFF CREWS - - JCREWS@PALMCOASTGOV.COM ENGIN1 COMPLETE 11/06/2023 11/07/2023 Note: Released By: TIM BAKER - (386)986-4726 - TBAKER@PALMCOASTGOV.COM SWALE COMPLETE 10/16/2023 12/05/2023 Note: Released By: TIM BAKER - (386)986-4726 - TBAKER@PALMCOASTGOV.COM BLD COMPLETE 10/13/2023 10/14/2023 Note: Released By: JPI CUSVC COMPLETE 10/13/2023 10/16/2023 Note: Released By: CYNTHIA SCHWEERS - - CSCHWEERS@PALMCOASSTGOV.COM ELEC HOLD 10/13/2023 10/16/2023 Note: Held By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM1. Submit a 400 amp riser diagram. ENGIN1 COMPLETE 10/13/2023 10/16/2023 Note: Released By: TIM BAKER - (386)986-4726 - TBAKER@PALMCOASTGOV.COM GAS CANCEL 10/13/2023 10/16/2023 LOCATE COMPLETE 10/13/2023 10/17/2023 Note: Released By: CANDACE BOWERMASTER - - CBOWERMASTER@PALMCOASTGOV.COM MECH COMPLETE 10/13/2023 10/16/2023 Note: Released By: CHRIS PISCITELLI - (386)986-2574 - CPISCITELLI@PALMCOASTGOV.COM SW1 HOLD 10/13/2023 10/24/2023 Note: Held By: GABRIEL BERTOLA - (386)986-7660 - GBERTOLA@PALMCOASTGOV.COMSod elevations adjacent to the structure are 4” below the FFE for block and 6” forwood frame structures. (D)Culvert material and size to be depicted. Typical is 17X13 CMP (L) ZON HOLD 10/13/2023 10/16/2023 Note: Held By: KATIE TAING - (386)986-3751 - KTAING@PALMCOASTGOV.COMMust have separation between front of home with walkway and additional foundation plantings.Provide NEW Site plan and Landscape plan showing the separation. BADMIN COMPLETE 10/13/2023 10/16/2023 Note: Released By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM
Permit Search | Palm Coast Connect (2024)
Top Articles
Latest Posts
Article information

Author: Lakeisha Bayer VM

Last Updated:

Views: 6254

Rating: 4.9 / 5 (49 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Lakeisha Bayer VM

Birthday: 1997-10-17

Address: Suite 835 34136 Adrian Mountains, Floydton, UT 81036

Phone: +3571527672278

Job: Manufacturing Agent

Hobby: Skimboarding, Photography, Roller skating, Knife making, Paintball, Embroidery, Gunsmithing

Introduction: My name is Lakeisha Bayer VM, I am a brainy, kind, enchanting, healthy, lovely, clean, witty person who loves writing and wants to share my knowledge and understanding with you.